Pengembangan Data Logger Suhu Otomatis Berbasis Arduino Dengan Sensor DS18B20 Untuk Praktikum

Pengembangan Data Logger Suhu Otomatis Berbasis Arduino Dengan Sensor DS18B20 Untuk Praktikum

  • Riswanto Riswanto
  • M.Barkah Salim Universitas Muhammadiyah Metro
  • Arif Hidayat Universitas Muhammadiyah Metro
  • Azmi Sari Rinjani Universitas Muhammadiyah Metro
  • Selva Sasmita Universitas Muhammadiyah Metro
Keywords: arduino, automatic data logger, calorimeter, DS18B20, temperature measurement

Abstract

This study developed and evaluated an Arduino-based automatic temperature data logger using a DS18B20 sensor for calorimeter practicums. The development followed the Analysis, Design, Development, Implementation, and Evaluation stages. The sensor was connected to an Arduino Uno and programmed to record temperature every 15 s, eliminating manual reading and transcription during the thermal process. Operational performance was assessed from data completeness, temperature change (ΔT), time required to reach an operational equilibrium criterion, and the range of the final three readings. In the water-mixing test, the temperature increased from 26.62 °C to 39.56 °C (ΔT = 12.94 °C), with a 0.06 °C range in the last three observations. In the metal-response test, the recorded temperature increased from 25.81 °C to 28.94 °C (ΔT = 3.13 °C), and the last three readings were identical. All planned records were stored, giving 100% data completeness. These results show that the system functioned reliably as an automatic logger and supported objective identification of thermal stabilization. The available data, however, do not establish metrological accuracy because calibration against a traceable reference and replicated uncertainty analysis were not performed. The device is therefore acceptable for automated temperature recording in introductory calorimetry, while further calibration is required before it is used for precise determination of specific heat.

References

Abrahams, I., & Millar, R. (2008). Does practical work really work. A Study of the Effectiveness of Practical Work as a Teaching and Learning Method in School Science. International Journal of Science Education, 30(14), 1945–1969. https://doi.org/10.1080/09500690701749305
Baden, T., Chagas, A. M., Gage, G., Marzullo, T., Prieto-Godino, L. L., & Euler, T. (2015). Open Labware: 3-D Printing Your Own Lab Equipment. PLOS Biology, 13(3), e1002086. https://doi.org/10.1371/journal.pbio.1002086
Branch, R. M. (2009). Instructional Design: The ADDIE Approach. Springer US. https://doi.org/10.1007/978-0-387-09506-6
Brinson, J. R. (2015). Learning outcome achievement in non-traditional (virtual and remote) versus traditional (hands-on) laboratories: A review of the empirical research. Computers & Education, 87, 218–237. https://doi.org/10.1016/j.compedu.2015.07.003
Casaburo, F. (2022). Measurement of the Newton’s cooling law time-constant by Arduino: an idea for STEM education in high schools. Physics Education, 57(6), 063001. https://doi.org/10.1088/1361-6552/ac8408
Chanthamanee, P., Jinda, P., Mani, M., & Prasitpong, S. (2021). Newton’s law of cooling experiment set using Arduino temperature sensor. Journal of Physics: Conference Series, 2145(1), 012068. https://doi.org/10.1088/1742-6596/2145/1/012068
Çoban, A., & Salar, R. (2023). Analyzing Position, Velocity and Acceleration Graphs using Arduino. Jurnal Pendidikan Fisika Indonesia, 19(1), 36–46. https://doi.org/10.15294/jpfi.v19i1.32246
Etkina, E., Karelina, A., Ruibal-Villasenor, M., Rosengrant, D., Jordan, R., & Hmelo-Silver, C. E. (2010). Design and Reflection Help Students Develop Scientific Abilities: Learning in Introductory Physics Laboratories. Journal of the Learning Sciences, 19(1), 54–98. https://doi.org/10.1080/10508400903452876
Finkelstein, N. D., Adams, W. K., Keller, C. J., Kohl, P. B., Perkins, K. K., Podolefsky, N. S., Reid, S., & LeMaster, R. (2005). When learning about the real world is better done virtually: A study of substituting computer simulations for laboratory equipment. Physical Review Special Topics - Physics Education Research, 1(1), 010103. https://doi.org/10.1103/PhysRevSTPER.1.010103
Geschwind, G., Vignal, M., Caballero, M. D., & Lewandowski, H. J. (2024). Using a research-based assessment instrument to explore undergraduate students’ proficiencies around measurement uncertainty in physics lab contexts. Physical Review Physics Education Research, 20(2), 020105. https://doi.org/10.1103/PhysRevPhysEducRes.20.020105
Heradio, R., de la Torre, L., Galan, D., Cabrerizo, F. J., Herrera-Viedma, E., & Dormido, S. (2016). Virtual and remote labs in education: A bibliometric analysis. Computers & Education, 98, 14–38. https://doi.org/10.1016/j.compedu.2016.03.010
Hibbert, D. B., Korte, E. H., & Örnemark, U. (2021). Metrological and quality concepts in analytical chemistry (IUPAC Recommendations 2021). Pure and Applied Chemistry, 93(9), 997–1048. https://doi.org/10.1515/PAC-2019-0819/XML
Hofstein, A., & Lunetta, V. N. (2004). The laboratory in science education: Foundations for the twenty‐first century. Science Education, 88(1), 28–54. https://doi.org/10.1002/sce.10106
Holmes, N. G., & Wieman, C. E. (2018). Introductory physics labs: We can do better. Physics Today, 71(1), 38–45. https://doi.org/10.1063/PT.3.3816
Holmes, N. G., Wieman, C. E., & Bonn, D. A. (2015). Teaching critical thinking. Proceedings of the National Academy of Sciences, 112(36), 11199–11204. https://doi.org/10.1073/pnas.1505329112
Itterheimová, P., Foret, F., & Kubáň, P. (2021). High-resolution Arduino-based data acquisition devices for microscale separation systems. Analytica Chimica Acta, 1153, 338294. https://doi.org/10.1016/j.aca.2021.338294
Kubínová, Š., & Šlégr, J. (2015). Physics demonstrations with the Arduino board. Physics Education, 50(4), 472–474. https://doi.org/10.1088/0031-9120/50/4/472
Leitão, U. A. (2024). RLab Calorimetry: an internet-enabled calorimeter using Arduino for local or remote lab activities. Physics Education, 59(4), 045018. https://doi.org/10.1088/1361-6552/ad4539
Ma, J., & Nickerson, J. V. (2006). Hands-on, simulated, and remote laboratories. ACM Computing Surveys, 38(3), 7. https://doi.org/10.1145/1132960.1132961
Madrigal, P., Rama, R., Sánchez, M., Mustelier, C., Alfaro, P., Presa Madrigal, L., Antonio Rodríguez Rama, J., Martín Sánchez, D. A., Costafreda Mustelier, J. L., Ángel Sanjuán, M., & Luis Parra Alfaro, J. (2024). Cost-Effective Temperature Sensor for Monitoring the Setting Time of Concrete. Applied Sciences 2024, Vol. 14, Page 4344, 14(11), 4344. https://doi.org/10.3390/APP14114344
Meltzer, D. E. (2004). Investigation of students’ reasoning regarding heat, work, and the first law of thermodynamics in an introductory calculus-based general physics course. American Journal of Physics, 72(11), 1432–1446. https://doi.org/10.1119/1.1789161
Molenda, M. (2003). In search of the elusive ADDIE model. Performance Improvement, 42(5), 34–36. https://doi.org/10.1002/pfi.4930420508
Nichols, D. (2017). Arduino-Based Data Acquisition into Excel, LabVIEW, and MATLAB. The Physics Teacher, 55(4), 226–227. https://doi.org/10.1119/1.4978720
Nuraini, S., Suseno, N., Riswanto, R., & Harjati, P. (2021). Perbandingan Hasil Belajar Dan Kualitas Kolaborasi Siswa Antara Kelompok Kecil Dan Kelompok Besar Dalam Pembelajaran Menggunakan Metode Eksperimen. Jurnal Firnas, 2(1), 19–27. https://doi.org/10.24127/FIRNAS.V2I1.3400
Pearce, J. M. (2012). Building Research Equipment with Free, Open-Source Hardware. Science, 337(6100), 1303–1304. https://doi.org/10.1126/science.1228183
Potkonjak, V., Gardner, M., Callaghan, V., Mattila, P., Guetl, C., Petrović, V. M., & Jovanović, K. (2016). Virtual laboratories for education in science, technology, and engineering: A review. Computers & Education, 95, 309–327. https://doi.org/10.1016/j.compedu.2016.02.002
Riswanto, R., Alarifin, D. H., Suseno, N., Harjati, P., & Putra, D. hartanto S. (2024). Efisiensi Praktikum Fisika Melalui Penyajian Laporan Hasil Praktikum Berbasis Video Projek Dalam Menumbuhkan Kemampuan Self-Learning Mahasiswa. Jurnal Pendidikan Fisika, 12(2), 171. https://doi.org/10.24127/jpf.v12i2.10920
Riswanto, R., & Dewi, N. A. K. (2017). Peningkatan Keterampilan Proses Sains Melalui Pembelajaran Berbasis Laboratorium Untuk Mewujudkan pembelajaran Berkarakter. Jurnal Riset Dan Kajian Pendidikan Fisika, 4(2), 60. https://doi.org/10.12928/jrkpf.v4i2.8164
Riswanto, R., Hidayat, A., & Salim, M. B. (2025). Optimizing digital learning through the ADDIE instructional approach in an arduino based automatic plant watering prototype project using a capacitive soil and moisture sensor. Compton: Jurnal Ilmiah Pendidikan Fisika, 12(1), 1–15. https://doi.org/10.30738/CJIPF.V12I1.19645
Riswanto, R., Prihandono, E., Hidayat, A., & Riswanto, W. R. A. (2025). Prototipe smart guidance stick tunanetra berbasis Arduino dengan sensor HC-SR04 sebagai projek dalam pembelajaran digital. Jurnal Firnas, 6(1), 34–46. https://doi.org/10.24127/jurnal%20firnas.v6i1.8596
Riswanto, Suseno, N., Partono, Harjati, P., & Dedy, H. A. (2019). School Laboratory Management Information System. Journal of Physics: Conference Series, 1361(1). https://doi.org/10.1088/1742-6596/1361/1/012068
Santoso, T., Riswanto, R., Suseno, N., & Sukarelawan, Moh. I. (2022). Pengembangan smart box berbasis digital dengan memanfaatkan arduino uno sebagai sumber belajar fisika. Berkala Fisika Indonesia : Jurnal Ilmiah Fisika, Pembelajaran Dan Aplikasinya, 13(2), 72. https://doi.org/10.12928/bfi-jifpa.v13i2.22809
Sari, M., Riswanto, R., & Prihandono, E. (2022). Pengembangan Alat Water Monitor Pada Budidaya Ikan Air Tawar Menggunakan Mikrokontroler Arduino Sebagai Sumber Belajar Fisika. Jurnal Firnas, 3(2), 8–21. https://doi.org/10.24127/firnas.v3i2.3414
Sari, W. M., Riswanto, R., & Partono, P. (2019). Validitas Mobile Pocket Book Berbasis Android Menggunakan Adobe Flash Pada Materi Suhu Dan Kalor. Berkala Ilmiah Pendidikan Fisika, 7(1), 35. https://doi.org/10.20527/bipf.v7i1.5728
Smetana, L. K., & Bell, R. L. (2012). Computer Simulations to Support Science Instruction and Learning: A critical review of the literature. International Journal of Science Education, 34(9), 1337–1370. https://doi.org/10.1080/09500693.2011.605182
Suseno, N., & Riswanto, R. (2017). Sistem Pengelolaan Laboratorium Fisika Untuk Mewujudkan Pelaksanaan Praktikum Yang Efisien. Jurnal Pendidikan Fisika, 5(1), 76. https://doi.org/10.24127/jpf.v5i1.743
Suseno, N., Riswanto, R., Aththibby, A. R., Alarifin, D. H., & Salim, M. B. (2021). Model Pembelajaran Perpaduan Sistem Daring dan Praktikum untuk Meningkatkan Kemampuan Kognitif dan Psikomotor. Jurnal Pendidikan Fisika, 9(1), 42. https://doi.org/10.24127/jpf.v9i1.3169
Syamsiah, E. N., Taufani, M. R., Aminudin, A. H., Pamungkas, R. S., Fadilla, R. M., & Nabilah, F. N. (2024). Development of the Physics Practicum Apparatus based on Microcontroller: A Prototype Constructed from Misconceptions of Basic Kinematics Concepts. Jurnal Penelitian & Pengembangan Pendidikan Fisika, 10(2), 367–380. https://doi.org/10.21009/1.10213
Tufino, E., & Organtini, G. (2024). Evaluation of the Effectiveness of an Introductory Mechanics Laboratory with Arduino and Smartphone. In S. Faletič & J. Pavlin (Eds.), Teaching and learning physics effectively in challenging times (pp. 161–174). Springer. https://doi.org/10.1007/978-3-031-72541-8_11
Vallejo, W., Diaz-Uribe, C., & Fajardo, C. (2020). Do-it-yourself methodology for calorimeter construction based in Arduino data acquisition device for introductory chemical laboratories. Heliyon, 6(3), e03591. https://doi.org/10.1016/j.heliyon.2020.e03591
Wilcox, B. R., & Lewandowski, H. J. (2016). Open-ended versus guided laboratory activities:Impact on students’ beliefs about experimental physics. Physical Review Physics Education Research, 12(2), 020132. https://doi.org/10.1103/PhysRevPhysEducRes.12.020132
Wörner, S., Kuhn, J., & Scheiter, K. (2022). The Best of Two Worlds: A Systematic Review on Combining Real and Virtual Experiments in Science Education. Review of Educational Research, 92(6), 911–952. https://doi.org/10.3102/00346543221079417
Published
2026-10-29